Cut two wooden dowels to the desired length. You can use one piece of dowel and cut it in two, or you can use two separate pieces and cut them each to length. You can use a small hacksaw, or a box cutter will work, as well. Try to get the ends as smooth as possible.[1] X Research source Do this outside or over a trashcan to reduce the mess. This length will be determined by the size of kite you want to make. The dowels can be the same length or one can be shorter. For example, both could be 40 inches, or one could be 32” and the other 24”. It’s up to you the exact shape you want for your kite. Notch the ends of the dowels. Using the saw or knife, cut notches into the ends, in which a piece of kite string will sit. The notches don’t need to be very deep, just enough that the string will fit in. Make sure the notches on each end of each dowel are going the same direction.[2] X Research source Form a cross with the dowels. If you used two lengths, the longer one will be vertical and the shorter one will be horizontal. Place the horizontal dowel ? of the way from the top of the vertical dowel. Make sure the vertical dowel’s notches are pointing sideways toward the horizontal

dowel, and the horizontal dowel’s notches are pointing vertically toward the vertical dowel. Tie the dowels together. You’ll need about 12 inches (30 cm) of kite string. Circle the string around each angle formed by the crossed dowels. As you tie the string, make sure the dowels stay at 90 degree angles. Knot the string around the cross section multiple times so the dowels are held tight. Wrap string around the bottom of the vertical dowel. Starting at the bottom of the vertical dowel, wrap the kite string around five or six times. Make sure that when you finish wrapping, the string is near the end of the dowel again. The purpose of this is to anchor the string to the frame securely before you wrap it around the frame. Wrap the string around the frame through the notches. Starting with the bottom where you wrapped the string already, stretch the string from one notch to the next, making sure it stays tight.[3] X Research source Finish by hooking the string through the bottom notch and tying it off. The purpose of wrapping string around the frame is to help it maintain its shape when you fly the kite. It also gives you a guide for cutting the body out. Trace around the frame on

a large sheet of paper. Newspaper usually works well for this, if it is big enough. If you can’t find a newspaper large enough, any large craft paper will work. As you draw around the string frame, leave about 1 inch (2.5 cm) extra around it. You don’t need to be too careful about making perfectly straight lines because what you trace will be folded later. Cut out the kite shape. Set the frame to the side and cut the kite shape out. You can discard the extra paper, as you won’t need it anymore. Be careful to stay right on the line, or even outside it a little bit, so you don’t cut the kite too small. Once you have finished cutting it out, lay it flat on the table and lay the frame on top of it. Fold the edges of the paper over the string and tape it in place. Make sure the frame is centered on the kite body. Going around the kite one side at a time, fold the paper over the string. Tape the corners first and then put some tape around each folded edge. For extra support, you can put a few pieces of tape along the dowels to secure them in place. Tie a string around the cross section. Now that the kite is fully constructed, tie a string to it, which you will hold when you fly

the kite. You’ll want it to be around 20 yards (18 meters) or so. Make sure it’s long enough that the kite can fly freely. Make a mark for the top point of the kite. Lay a large trash bag flat on the table. Bags meant for outdoor use are ideal because they are made of thicker material. Use a soft tip marker to make the first mark a few inches below the top, along the left edge of the bag. The edge of the bag will become the center of the kite. The trash bag you use needs to be at least 40 inches (100 cm) long for this kite. Depending on the color of the trash bag, make sure the marker you use is visible. For example, with a black trash bag a silver marker would work best. Measure a point for the side corners of the kite. Using a yardstick or tape measure, measure 10 inches (25 cm) down the edge of the bag. Then measure 20 inches (50 cm) across, which should be somewhere in the middle of the bag. Make a mark here for the side corners.[4] X Research source Measure and mark the bottom point. From the top point, measure 40 inches (100 cm) down on the edge of the bag and make a mark. The three points should now form a triangle on the bag, with the side corner mark being closer to

the top mark. If you only have trash bags that are smaller than the given measurements, just make sure your points are proportional. The mark for the side corner should measure half of the total length, so that when the bag is unfolded the length and width are the same. For example, the horizontal span could be measured at 10 inches (25 cm) and the length could be 20 inches (50 cm). As long as the proportions match, a smaller kite is fine. Connect the dots with a marker. Using the yardstick or another straight edge as a guide, connect the top point to the side corner point and the side corner point to the bottom point. Your line doesn’t have to be perfectly straight, but as close as possible. Cut the shape out. Use sharp scissors or a box knife and cut as straight as you can along the lines. If you are going to use a box knife, you’ll want to put a large piece of cardboard under the material before you cut it out. Save the extra material after you cut the kite shape out. This will be used later. After you cut the kite out, unfold the diamond shape and lay it flat on the table. Cut wooden dowels or bamboo sticks to 40 inches (100 cm). The dowels will be used as the frame of the

kite. If you can purchase them already cut to size, that’s great, but if not, you’ll need to carefully cut them down. Use ? inch (.6 cm) dowels. Use either a small hacksaw or a box cutter to trim the dowels to size. Do this either outside or over the trashcan to avoid leaving sawdust all over. If you made the body of the kite smaller than 40 inches in length, cut the dowels to the length you measured the body at. Form a cross with the sticks and tie them at the intersection. The horizontal stick should be about 10 in (25 cm) from the top of the vertical stick. Using kite string, about 12 in (30 cm) or so, tie it tightly around the intersection of the sticks. Make a few knots so the sticks are tightly secured together.[5] X Research source It doesn’t matter too much how you tie the string here, as long as the sticks are secured together. You can also put some tape or glue over the string for added strength. Attach the frame to the plastic body of the kite. Make a small cut on each of the corners of the kite. Fold these flaps over the dowel pieces and tape them securely in place. Duct tape is best, but just make sure the tape holds the frame to the body securely. Once the

corners are attached, you can place 2-4 pieces of tape along each dowel so the kite is secured across the whole body of the kite. Tie a 2 foot long strip of the plastic to the bottom of the kite. This is the tail of the kite, which will help stabilize it in the wind. You can also tie shorter strips onto the main tail for extra drag. To add more color, you could use bright strips of cloth instead. Attach the remaining kite string to the frame of the kite. Poke 4 small holes through the plastic around the center of the crossed dowels, one hole in each angle of the cross. Lead the kite string through all four holes and tie securely to the center cross section. This is the string which you will hold when you fly the kite, so make sure it is plenty long enough. How high a kite can fly will depend on the wind, but you’ll probably want at least 20 yards (18 meters) of string.