Position the jack on flat, level ground. This prevents the jack from rolling while you work on it. It also keeps the oil level so you can fill the chamber accurately.[1] X Research source Also place the jack somewhere that can get dirty, just in case you spill some oil. If you don't want oil in your driveway, try doing this in the street. Open the release valve. This lowers the jack so you can access the filler plug. Different jacks may have different release mechanisms. On some jacks, turning the handle counterclockwise lowers the press. On others, you have to press a release valve in a different spot.[2] X Research source If you’re unsure how your jack releases, consult your owner’s manual. Keep the release valve open while you work. Remove the cover plate if your jack has one. Depending on your jack model, there may be a cover plate that protects the jack’s internal mechanism. Remove any screws holding this cover in place. Then lift the cover off.[3] X Research source Depending on the type of jack you have, the cover plate might come off entirely or just lift up. If the plate comes off, keep it in a safe place so you don’t lose it. Usually these screws require a Phillips

head screwdriver, but check your particular model to see what type of screwdriver you need. Don’t lose the screws you remove. Keep them in a safe place so you can put the cover back on later. Wipe the area around the filler port plug. The filler port is where you will pour the oil. To prevent contamination, use a rag and clean off the area around the filler plug. This keeps dirt out of the oil reservoir.[4] X Research source If your jack is old and there is a lot of caked on dirt around the fill plug, try spraying a hose or pressure washer to remove the gunk first. Remove the filler port plug. This plug is underneath the cover plate on most jacks. Depending on your jack model, the plug might unscrew or just pop out. If it is a screw type, use a screwdriver and turn counterclockwise to remove the plug. If it pops out, insert a flathead screwdriver under the plug and lift it out.[5] X Research source If you can’t locate the filler port, check the owner’s manual for your jack. Be careful not to damage the plug when you remove it. If it doesn’t come out easily, stop and reassess what you’re doing. Don’t force it out. Fill the reservoir with hydraulic jack oil. Pour until

the oil is just below the lower rim of the fill hole, then stop. Wipe away any excess oil on the rim before replacing the plug.[6] X Research source Use a funnel to avoid spills. Do not use any other type of oil besides hydraulic jack oil. Motor oil or brake fluid will not work. Replace the filler plug. Either push the plug back into the hole or screw it back in by turning it clockwise. After the plug is in place, follow the procedure to bleed air out of the hydraulic system.[7] X Research source Do not replace the cover plate yet. You still need to bleed the air from the mechanism before moving on, and the cover plate will get in the way. Depending on the jack model, you may also have to keep the fill plug out while you bleed the air. Consult your owner’s manual for the correct process. Confirm that the release valve is open. The release valve should still be open from when you filled the jack with oil, but double check. Open the release mechanism completely to lower the jack. Leave the release valve open while bleeding the air.[8] X Research source The bleeding process is important because air can build up in the hydraulic system while you change the oil. If air is in the

system, the jack won't rise properly and could even collapse. Bleeding the jack removes the air and makes the jack function correctly. Pump the handle quickly 10-15 times with the release valve open. This pushes air out of the jack system. With the release valve open, the jack shouldn’t rise while you pump. If it starts rising, double check to make sure the release valve is open.[9] X Research source Some jack models have different variations on how to bleed the air. Check with your owner’s manual to see if your model uses a different method. Close the release valve and test the jack. Turn the handle clockwise to close the release valve, then pump the jack. It should rise in smooth, even motions. Pump it all the way to the top and then release it.[10] X Research source If the jack is jerky or doesn’t rise to the top, there is probably still air in the system. Repeat the bleeding procedure in this case. Replace the cover plate. With the process done, you can now reinstall all the pieces you removed. Put the cover plate back in place and screw it in with the screws you removed before.[11] X Research source